A
ALTIUS CMFacade · Roofing · Construction Mgmt
FACADE RESTORATION

Facade Repair Methods Explained: Repointing, Lintels, Crack Stitching, Parapets and Sealant

Published November 8, 2026

Which facade repair fixes which facade problemFive rows pair a facade problem with the repair that addresses it. Failed mortar joints: repointing. Failed movement joints and perimeter joints: sealant replacement. Corroding or moving steel that supports masonry: lintel and shelf angle repair. Cracked masonry: crack stitching. The most exposed part of the wall: parapet rebuilds.Facade problemRepairfailed mortarjointsRepointingfailed movementjoints andperimeter jointsSealantreplacementcorroding ormoving steelthat supportsmasonryLintel andshelf anglerepaircracked masonryCrackstitchingthe most exposedpart of the wallParapetrebuildsRepair choice follows cause
Failed mortar joints: repointing. Failed movement joints and perimeter joints: sealant replacement. Corroding or moving steel that supports masonry: lintel and shelf angle repair. Cracked masonry: crack stitching. The most exposed part of the wall: parapet rebuilds. Repair choice follows cause.

What repair fixes which facade problem?

Start with the cause.

Repointing is for failed mortar joints. Sealant replacement is for failed movement joints and perimeter joints. Lintel and shelf angle repair deals with corroding or moving steel that supports masonry. Crack stitching reconnects cracked masonry. Parapet rebuilds address the most exposed part of the wall.

The repair scope on a FISP job comes from what the inspector found. If you need the filing side and timing, see FISP ratings explained. If you need cost planning, see budgeting a facade restoration.

The methods below track what the National Park Service (NPS), Brick Industry Association (BIA), ASTM standards, and DOB’s FISP rule say, and only that.

How does the inspector tell maintenance from structural?

BIA Technical Note 46 gives you a workable line.

It lists these as examples of structural conditions: cracks in brick wider than 0.075 inch (2 mm), cracks through multiple brick units, cracks in a stepped or diagonal pattern, widespread spalled brick, accumulated rust on lintels or shelf angles, out-of-plane movement, and neutral or negative slope on sills. Those issues generally call for a professional engineer to find the cause and recommend the repair.

DOB’s rule lines up with that. Under 1 RCNY 103-04, the QEWI has to look for cracking of masonry, loosening or corrosion of metal anchors and supports, water entry in cavities, and movement of lintels and shelf angles, and has to determine the cause.

That’s the point. Repair choice follows cause.

How does repointing work?

Repointing means cutting out deteriorated mortar to a uniform depth and putting new mortar back in. BIA says you use it when mortar erosion goes beyond 1/4 inch, when mortar is crumbling, when there are voids, hairline cracks in the mortar, or cracks between brick and mortar.

NPS Preservation Brief 2 lays out the parts that matter on the job:

  • Depth. Remove old mortar to at least 2 to 2-1/2 times the joint width, about 1/2 to 1 inch for most brick joints. BIA gives a minimum of twice the joint width, generally 3/4 inch.
  • Tools. Hand chisels and hammers are the least damaging. Power saws on thin joints almost always damage brick edges. Grinders are acceptable only with skilled masons, on certain horizontal joints and never on vertical joints, per the Brief.
  • Mortar. New mortar must be as soft or softer than the historic mortar and softer, with greater vapor permeability, than the masonry units. The Brief says hard portland-cement mortar that is less permeable than soft brick has caused severe damage to a brick wall.
  • Placement. Fill deep joints first, then pack the joint in layers of about 1/4 inch.
  • Test panel. A panel of about 3 feet by 3 feet on brickwork sets the standard for the job.

Preservation Brief 2 also says repointing takes time, and scaffolding may need to stay up for an extended period. Plan it with other wall work.

What is lintel and shelf angle repair?

Lintels and shelf angles are steel members that carry masonry over openings and at floor lines.

When that steel corrodes, rust takes up more volume than the steel did. An NPS technical note calls that oxide jacking. That expansion displaces, cracks, and spalls the surrounding masonry. BIA lists accumulated rust on lintels or shelf angles among conditions that need engineering review.

BIA Technical Note 18A shows what the restored detail has to include. Where a structure has shelf angles at each floor, it must have horizontal expansion joints under each angle, typically 1/4 inch high, sealed with backer rod and sealant at the toe. A loose-laid lintel needs a 1/8 to 1/4 inch space at each end so the steel can move.

For owners, the point is simple. The BIA detail around lintels and shelf angles includes the movement joints around the steel, not just the steel itself.

The field scope can vary a lot. The 529 West 42nd Street restoration, a $3M+ FISP 9 contract in progress, lists stone lintel patching and replacement, steel lintel replacement and shelf angle refurbishment among its items, along with parapet reconstruction and window sill pinning.

What is crack stitching?

Crack stitching shows up in a review in the journal Construction and Building Materials on stainless steel used for masonry repair and reinforcement.

The sources listed here do not spell out crack stitching for NYC facades, so this guide does not give bar sizes or spacing. Treat the method and its design as an engineer’s decision, especially because BIA says cracks over 0.075 inch and stepped cracks warrant a professional investigation first.

When does a parapet get rebuilt?

Under 103-04, a parapet is an appurtenance, along with copings and railings. BIA says sills, parapets, chimneys and copings see more severe exposure and may need repair at shorter intervals.

BIA’s table puts metal coping and flashing at 20 to 75 years before repair and plastic flashing at 5 to 25 years. Brick walls, by comparison, are put at 100 to 150 or more years.

Whether the right fix is repointing, replacement of units, or a full rebuild is an engineering decision tied to what the QEWI documents. Altius CM carries out parapet scopes the owner contracts for: 529 West 42nd Street includes full parapet reconstruction, and the Kips Bay Complex included parapet concrete repairs. For the annual observation duty on parapets, see NYC’s parapet observation requirement, and for scope detail, parapet repair.

How does sealant replacement work?

BIA’s procedure is straightforward: carefully remove deteriorated sealant, clean the opening, prime it, install an appropriately sized backer rod (bond-breaker tape if the joint is too small), and fill with a full bead of high-quality elastomeric sealant compatible with adjacent materials.

BIA says manufacturers recommend three generic types for brickwork: polyurethanes, silicones and polysulfides.

ASTM C920 covers cured single- or multi-component cold-applied elastomeric joint sealants. ASTM C1193 is a guide to joint sealant use. It says proper maintenance could include replacing local failures and possibly all the sealant, perhaps more than once, over a building’s design life. Its example is 50 years.

The amount of work can be small or very large. 150 West 56th Street replaced deteriorated window sealant and repaired stone panel cracks and joints as part of a completed $750K+ envelope job. The Kips Bay Complex replaced 80,000 linear feet of sealant and caulk.

For the full service scope see facade repair and replacement. Access for any of these repairs is covered in facade access methods.

Sources

Last verified: November 8, 2026. These sources are general guidance; the engineer of record and the project specification govern an actual repair. This is general information, not legal advice.

Frequently asked questions

How deep should old mortar be cut out before repointing?

The National Park Service's Preservation Brief 2 says old mortar should be removed to a minimum depth of 2 to 2-1/2 times the joint width, which for most brick joints is about 1/2 to 1 inch. The Brick Industry Association's Technical Note 46 gives a minimum of twice the joint width, generally 3/4 inch, or until sound mortar is reached.

Should repointing mortar be as hard as possible?

No. Preservation Brief 2 says repointing mortar should be softer and more vapor permeable than the masonry units and no harder or more impermeable than the historic mortar. It shows damage to soft brick from hard portland-cement mortar.

When is a crack a maintenance item and when is it structural?

BIA Technical Note 46 lists cracks wider than 0.075 inch (2 mm), cracks through multiple brick units, and stepped or diagonal cracks among the signs of structural issues, and says those generally warrant investigation by a professional engineer. Hairline mortar cracking is treated as a maintenance repair.

How long does facade sealant last?

BIA Technical Note 46 estimates 5 to 20 years for sealant in joints, against 100 to 150 or more years for brick walls. ASTM C1193 notes that a sealant joint may need localized replacement, and possibly complete replacement more than once, over a building's design life.

Who decides which repair a facade needs?

For a FISP building, the Qualified Exterior Wall Inspector documents and classifies conditions and the repair scope follows from the report. The repair contractor carries out the work. Engineering questions on structural cracking, lintels and parapets belong with the inspector or the owner's engineer.

Need this work scoped?

Contact Altius CM